Znaleziono 103 wyniki

autor: breckjensen
30 gru 2017, 11:51
Forum: Do szlifowania
Temat: Xyz calibration grinding bed
Odpowiedzi: 0
Odsłony: 263

Xyz calibration grinding bed

Hi, When it gets to point 3 (middle rear) it keeps grinding back and forth into the bed and I have to hit reset to prevent further damage. On Z calibration it hits bed lightly on 7 and slams down on 8 (middle rear) again I hit reset to prevent more damage. What is going on with the rear of the bed? ...
autor: breckjensen
30 gru 2017, 11:49
Forum: Do frezowania
Temat: Accuracy of Indexed End Mill Diameters?
Odpowiedzi: 0
Odsłony: 335

Accuracy of Indexed End Mill Diameters?

Hi, Here is a question that just occurred to me: will edge finders work with indexable tooling? I got my first carbide-insert end mill a while back. Should I be able to take the nominal diameter as gospe.? I didn't find the right solution from the internet. References: https://www.chaski.org/homemac...
autor: breckjensen
30 gru 2017, 11:48
Forum: Do frezowania
Temat: Horizontal Mill Spindle Direction?
Odpowiedzi: 0
Odsłony: 271

Horizontal Mill Spindle Direction?

Hi, I hope you'll all forgive me for this stupid newbie question. I'm ready to wire up the horizontal spindle motor on my Rockwell mill, and I'm wondering which direction is considered the "forward" direction for the spindle. Clockwise, or counter-clockwise as viewed from the table side of...
autor: breckjensen
30 gru 2017, 11:36
Forum: Do strugania
Temat: Scaling and Root Planing
Odpowiedzi: 0
Odsłony: 244

Scaling and Root Planing

Hi, At least I don't have to go on a business trip Thursday, like I was supposed. I told my boss I was having an outpatient surgical procedure (which, well, is only a little white lie, it feels more stressful and invasive than surgery to me!) and asked if I could do the meeting remotely, and he said...
autor: breckjensen
29 gru 2017, 12:48
Forum: Do szlifowania
Temat: Grinding Noise
Odpowiedzi: 0
Odsłony: 288

Grinding Noise

Hi, I just got my sous video device, and have only used it two times now. On the first use, I noticed that if I didn't put it into the mounting clamp just right, it would make a grinding noise. I got it to work, and my food was good. The second use, I had the same issue, but again, the food was good...
autor: breckjensen
29 gru 2017, 12:47
Forum: Do szlifowania
Temat: Help with Money grinding
Odpowiedzi: 0
Odsłony: 273

Help with Money grinding

Hi, So as the title suggests i need a bit of help, lvl 22 atm fishing in Oregon for Trout but i wanna know what else works well got decent Lure and float rig my only problem is my keepnet got the Fishcabin M atm i think, i know it has 11lb max and 66lb overall. For more details 2d animation video
autor: breckjensen
29 gru 2017, 12:45
Forum: Do wiercenia
Temat: Anyone seen any black-grass yet ?
Odpowiedzi: 0
Odsłony: 331

Anyone seen any black-grass yet ?

Hi, It was quite dry this autumn so alot of people got on and drilled up. It has stayed dry and so some herbicides might have been spent before this latest bit of rain. Are people seeing any grass weeds ? I didn't find the right solution from the internet. References: https://thefarmingforum.co.uk/i...
autor: breckjensen
29 gru 2017, 12:43
Forum: Do wiercenia
Temat: Your cut off date for autumn zero drilling?
Odpowiedzi: 0
Odsłony: 195

Your cut off date for autumn zero drilling?

Hi, Am I correct in thinking that it is not very advisable to zero till as late in the autumn as with min till or conventional tillage? I didn't find the right solution from the internet. References: https://thefarmingforum.co.uk/index.php?threads/your-cut-off-date-for-autumn-zero-drilling.197436/ C...
autor: breckjensen
28 gru 2017, 11:18
Forum: Do toczenia
Temat: Emco Unimat 3 - new bearings ?
Odpowiedzi: 0
Odsłony: 335

Emco Unimat 3 - new bearings ?

Hi, I'd like to replace the headstock sealed bearings on my Emco Unimat 3, they are 40 years old and the casing is dented. Does anyone know exactly what size they are and where to get them ? I didn't find the right solution from the internet. References: http://www.ukworkshop.co.uk/forums/emco-unima...
autor: breckjensen
28 gru 2017, 11:14
Forum: Do frezowania
Temat: Horizontal Mill Spindle Direction?
Odpowiedzi: 0
Odsłony: 237

Horizontal Mill Spindle Direction?

Hi, I hope you'll all forgive me for this stupid newbie question. I'm ready to wire up the horizontal spindle motor on my Rockwell mill, and I'm wondering which direction is considered the "forward" direction for the spindle. Clockwise, or counter-clockwise as viewed from the table side of...

Wyszukiwanie zaawansowane